| Menu | JAQForum Ver 26.09 |
Forum Index : Microcontroller and PC projects : HC-12 legal channels (in NZ)
for anyone interested, attached is a PDF listing those HC-12 channels that can be legally used in New Zealand, based upon data from "Radiocommunications Regulations (General User Radio Licence for Short Range Devices) Notice 2022", see: https://gazette.govt.nz/notice/id/2022-go3100 in summary, along with channels 1, 2, 3, and 4 at any speed and up to 25mW transmitting power, you can also legally use: - channel 64 at up to 2400 baud and 100mW transmitting power, and, - channel 96 at up to 38400 baud and 100mW transmitting power. the speed limits for channel 64 and 96 are to ensure that the transmission bandwidth remains entirely within the upper and lower bounds of the respective block of spectrum. while channels 28, 29, and 93 also fall within available spectrum, their use is reserved for biomedical telemetry and thus should be avoided. HC-12 legal channel table (NZ).pdf fyi, i've been looking into this for an application involving monitoring of a sewerage system that (for compliance) requires occasional reporting of short packets of status information back to a control panel located 100m from the tanks. i wanted to put the data on a 'less commonly used' frequency to avoid annoying anyone's garage door opener! cheers, rob :-) updated PDF file to correct AI errors that slipped through for channels 28,29,93 as well as added in a table of bandwidth info associated with each of the four 'air baud rate' values. Edited 2026-11-08 02:15 by robert.rozee |
||||||
Yes, I use channel 64 myself at 1200 baud. Last time I looked, it was UNRESTRICTED on that band, up to 500mW. 458.600MHz No matter, cos the HC12 can't do more then 100mW max anyway. Have you ever looked at the output of an HC12 on a spectrum analyser? They're pretty good! No harmonics of any detectable level for the 1st, 2nd and 3rd. Not what you might expect from such a cheap RF module. |
||||||
i probably should have noted in the PDF that apart from the one column labelled "Gazette Band Limits" all the other numeric data was from the perspective of using an HC-12, hence 100mW is mentioned as the maximum power 'achievable from an HC-12'. similarly the "Maximum Legal Air Baud" is not that calculated but instead taken from the list of rates supported by the HC-12; some of the bands could accommodate a higher rate, but the HC-12 has no means of using them. the table was produced with the assistance of Google's Gemini, although Gemini made quite a few glaring mistakes during the Q&A process that i needed to 'forcefully' point out. as always, she was very apologetic when her errors were shown. no, i don't have a spectrum analyser, but would be really interested in seeing plots for each of the nine HC-12 channels (1,2,3,4,28,29,64,93,96) tested at each of the eight possible UART baud rates it would be useful information to include in the HC-12 manual.cheers, rob :-) |
||||||
I'll put that on the "To-do" pile. ![]() |
||||||
Some photos from my spectrum analyser: (all at 1200 baud, FU4 mode) ![]() 200MHz span: ![]() 500MHz span: ![]() 1GHz span: ![]() 2nd Harmonic: (un-measurable from floor noise) ![]() 3rd Harmonic: (un-measurable from floor noise) ![]() VERY clean output, and MUCH better then I ever thought a $6 RF module would be. I expect any other frequency or baud rate would deliver similar results. |
||||||
it does indeed look very clean - i'm impressed! if you zoom way in on the 458.6MHz, so the screen spans, say, just +/-20kHz each side, how sharp is the cutoff at the edges? the allocated spectrum block ends at 458.61MHz, just 10kHz above the centre frequency? by various calculations i found online, 2400 baud should just be legal. cheers, rob :-) |
||||||
I was really rather impressed too, first time I tested these, cos that is NOT the norm, for cheap RF modules out of China. FM radio transmitters are notoriously horrible with their output, for MOST of those cheap ones out of China. I HAVE found some really good ones, but a lot of them, the harmonics are BAD! Sometimes as bad as to be only a few dB down on the strength of the carrier, and that is NOT a good thing! But the little HC-12 is really VERY good, and WAY better then I EVER thought it would be under test. They are 100% compliant with RSM(Radio Spectrum Management) rules with regard to RF output, harmonics and spurious emissions etc. As Rob and I both know though, it is easily possible to program the HC-12 module to operate on frequencies they are not allowed to be on, so it really is users responsibility to ensure you use them in the bands they are allowed to be used on. Even the CLEANEST signal in the world - if it is transmitting on a frequency it should not be on, the radio inspector can still come down on you like a ton of bricks, and rightly so. I'll do a 458.6MHz @ 50kHz span photo, and upload it here. My SA spans are 5/10/20/50/100/200/500/1000, so I can't select a span of 40kHz specifically, but the 50kHz span should still show you want you want to see. I plan to do your other requested frequencies/channels, but I can only do this stuff when I am not busy with something else, so it could be a while. Edited 2026-11-18 08:06 by Grogster |
||||||
Here are a couple more photos. Still 458.6MHz @ 1200 baud. 50kHz span: ![]() 100kHz span: ![]() I see the maximum modulation at about +6.5kHz, which is within the 10kHz spec. The CF is slightly off at 458.630MHz, but you can still calculate the deviation either side of the CF, by just looking at the grid-vs-span and working it out in your head. With a 50kHz span, each vertical line represents 5kHz, so as long as the modulation does not go more then two vertical grid lines horizontally either side of the CF, we're good for the 10kHz spec. If you want, I can do an EXACT 458.600MHz test tomorrow. I DID set 458.6MHz, but then when I zoomed in to 50kHz span, it shows it was a LITTLE off, and I never remembered to readjust the CF just a fraction! ![]() |
||||||
the allocated block of spectrum runs from 458.5400MHz to 458.6100MHz. if (some) HC-12 modules are sending out channel 64 on 458.630MHz (instead of 458.600MHz) that would see transmission outside of the block. this might be a problem :-( my guess is that the receiver side of the HC-12 is relatively wide. there is still the option of channel 96 (471.4MHz), where the allocated block of spectrum that it sits within extends from 471.0000MHz to 471.5000MHz, ie there is a 100kHz gap between the centre frequency of channel 96 and the edge of the block. cheers, rob :-) |
||||||
I've ordered a couple of these modules to play with. I don't have any real use for them, but its cool that these little modules exist. Probably the first program to do would be something that sweeps the full list of available channels and sees where the most reliable bandwidth is. (And which channels have the best range.) Another Claude task for the To Do list once the modules arrive! |
||||||
Be sure you buy authentic modules!!!! There are CHEAP CLONES out there, that use sub-standard crystals, and their frequency and modulation are HORRIBLE. See this thread: HC-12 Crystal Problems... You can also buy GENUINE ones from my website. @ Rob: I expect things are perfectly OK. As mentioned, I forgot to adjust the frequency once I zoomed in to 50kHz span. I will do another photo today with the analyzer adjusted for exactly 458.600MHz @ 50kHz span. The transmission is audible on my scanner on precisely 458.600MHz. I will also see if I can setup my frequency counter in the next test, just to help reinforce the data as being accurate. There are other frequency choices, as you mention. I forget the power you are allowed on channel 96, but I will look it up. It will be LESS then channel 64 though, cos that wee band of frequncies was "Unrestricted" up to 500mW last time I looked, but I think the other ones have power output limits lower then 100mW. I'll do a quick test of channel 96 too. Edited 2026-11-19 09:39 by Grogster |
||||||
Frequency counter says they are spot-on frequency. ![]() |
||||||
whew... that is a relief! cheers, rob :-) Edited 2026-11-19 15:17 by robert.rozee |
||||||
Not really what you would expect, performance/compliance wise, from such a cheap little RF module! I continue to be impressed with these little things. ![]() |
||||||
If that all is consistent within reasonable limits over production lots then they do their job really well. |
||||||
| The Back Shed's forum code is written, and hosted, in Australia. |