Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 13:23 05 Nov 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 366836 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 535760   02:49pm 16 Dec 2015
Normal Topics  

   Page 73 of 99    

Pipe coupling imsmooth, 24/06/2008 5 4737   09:51am 27 Jun 2008
is this the right fisher & paykel washer? Jpm000001, 25/06/2008 2 3786   12:49pm 25 Jun 2008
Books about vertical axis windmills Merlino, 24/06/2008 1 3931   02:50am 25 Jun 2008
Undergearing + Multipal Stators Hybrid, 08/06/2008 22 8075   05:14pm 23 Jun 2008
motor advice needed for beginner JW1111, 19/06/2008 4 4184   01:44am 23 Jun 2008
The Ugly Duckling sodes, 19/06/2008 10 9890   12:36pm 22 Jun 2008
Furling moe46, 21/06/2008 13 10604   04:28am 22 Jun 2008
Single blade windmill davef, 15/06/2008 12 6425   11:37pm 20 Jun 2008
how to figure rotor offset newbie-from-pa, 21/06/2008 1 4217   03:58pm 20 Jun 2008
vertical axis windmill blade design Merlino, 14/06/2008 19 5065   10:13am 19 Jun 2008
F and P bearing housings robbo, 18/06/2008 7 3583   09:59am 19 Jun 2008
Towers imsmooth, 09/06/2008 8 3913   10:36pm 18 Jun 2008
K220 regulator help Ayjay, 18/06/2008 3 3743   12:14pm 18 Jun 2008
guy cables imsmooth, 18/06/2008 2 3445   07:04am 18 Jun 2008
dc motor size need2know, 16/06/2008 4 3938   06:35pm 16 Jun 2008
The New Stator brucedownunder2, 09/06/2008 2 3540   07:23am 15 Jun 2008
On-site_blade balance check Gill, 14/06/2008 1 3258   02:33am 15 Jun 2008
Floating Turbines Magooly, 15/06/2008 1 3219   02:01am 15 Jun 2008
measuring rpm with hertz Ben, 11/06/2008 3 4489   06:31pm 12 Jun 2008
Township meeting imsmooth, 10/06/2008 2 3367   08:25am 10 Jun 2008
My memory is bugging me brucedownunder2, 09/06/2008 2 4211   09:27pm 09 Jun 2008
where to buy f&p kits? frank lee, 06/06/2008 1 3540   10:20pm 05 Jun 2008
Inverter question Fuzzer, 03/06/2008 2 3886   11:41am 05 Jun 2008
SWIFT TURBINES FandPwithPVC, 05/06/2008 1 3548   03:05am 05 Jun 2008
Pipe size imsmooth, 03/06/2008 2 4747   12:14pm 03 Jun 2008
= New posts since you last visited .      

   Page 73 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026