Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 11:03 31 Oct 2025 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 313 187626 Chopperp  10:11pm 16 Oct 2025
Forum Guidelines Gizmo, 11/12/2011 2 505844   02:49pm 16 Dec 2015
Normal Topics  

   Page 62 of 98    

Is the F&P 1" shaft adeuqate for ax flux? imsmooth, 19/02/2009 20 5393   04:06am 21 Feb 2009
Capacitors, dare I ask? KiwiJohn, 11/02/2009 12 4367   11:07pm 15 Feb 2009
Starting on the stator vawtman, 08/02/2009 9 3300   09:45pm 15 Feb 2009
3 Phase DaViD, 14/02/2009 2 2409   07:42am 15 Feb 2009
How much output can I expect heynow999, 15/02/2009 1 2557   07:36am 15 Feb 2009
F&P DaViD, 13/02/2009 1 2395   08:07pm 12 Feb 2009
Working load of steel cable imsmooth, 11/02/2009 3 2654   01:31pm 11 Feb 2009
resistance DaViD, 10/02/2009 2 2393   01:00pm 11 Feb 2009
lightning protection imsmooth, 09/02/2009 6 3458   02:32pm 10 Feb 2009
FIRE DaViD, 10/02/2009 0 2345   05:42pm 09 Feb 2009
avarage voltage DaViD, 07/02/2009 2 2904   05:29pm 09 Feb 2009
New Windmills & Mixing batteries RevUpWind, 06/02/2009 15 4902   12:02am 09 Feb 2009
wind wave turbine faroun, 02/02/2009 20 6048   12:15am 08 Feb 2009
car starter motor used as generator? iguana9999, 07/02/2009 6 13291   02:49am 07 Feb 2009
7.5HP Three Phase Motor Conversion SparWeb, 24/09/2008 54 32170   08:50pm 06 Feb 2009
miniture DaViD, 05/02/2009 4 2987   03:39pm 06 Feb 2009
no juice... birdhouse, 05/02/2009 5 2721   03:53pm 05 Feb 2009
motor DaViD, 06/02/2009 0 2504   03:08pm 05 Feb 2009
Neo conversion brucedownunder2, 03/02/2008 51 14680   02:52am 05 Feb 2009
Wiring for Savonius? Mr.Sleepy, 29/01/2009 13 4717   08:39pm 03 Feb 2009
Simple and accurate RPM measurement imsmooth, 31/01/2009 4 3339   06:37am 03 Feb 2009
10.5’ cedar/epoxy blades flying imsmooth, 02/02/2009 1 3137   05:10am 03 Feb 2009
Fisher & Paykel model preference catchnthe-)))), 01/02/2009 0 2637   03:56am 01 Feb 2009
Windmill System crazyk, 29/01/2009 16 4130   08:48am 31 Jan 2009
another newbie question birdhouse, 29/01/2009 15 4176   11:30pm 30 Jan 2009
= New posts since you last visited .      

   Page 62 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2025