Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 21:14 11 Sep 2025 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 310 181722 NomadAU  09:32pm 01 Sep 2025
Forum Guidelines Gizmo, 11/12/2011 2 500489   02:49pm 16 Dec 2015
Normal Topics  

   Page 65 of 98    

Measuring Generator Kwh Output? Wes Lemarr, 08/12/2008 9 8799   08:26am 08 Dec 2008
Is it safe to run an F&P without a load? Mr.Sleepy, 04/12/2008 7 3714   09:40am 06 Dec 2008
hi iam new here rolfkoedam, 14/11/2008 5 3817   06:44pm 03 Dec 2008
vertical windmills readyakira, 18/11/2008 19 16035   01:29pm 01 Dec 2008
Some thoughts on forces that destroy HAWT KiwiJohn, 30/11/2008 15 5801   01:13am 01 Dec 2008
Distance of tower from batteries? Moose, 27/11/2008 16 6440   10:06am 30 Nov 2008
A/C vs D/C for transmision readyakira, 26/11/2008 33 12529   11:19am 29 Nov 2008
aluminium chinese blades kumtarest, 01/08/2007 30 18195   07:59am 29 Nov 2008
VAWT up and going Gizmo, 12/11/2005 12 20311   06:19pm 27 Nov 2008
Dual stator Drag... robbo, 24/11/2008 11 3277   10:15pm 26 Nov 2008
downwind mill brucedownunder2, 24/11/2008 2 3535   11:57pm 23 Nov 2008
Masts or Towers eirbyte, 19/11/2008 5 3939   10:57am 21 Nov 2008
F&P Questions readyakira, 19/11/2008 0 2815   01:04pm 19 Nov 2008
A nice find. Gizmo, 06/10/2008 2 5205   02:05am 18 Nov 2008
Where do you buy blades Chinese? mimichris, 16/11/2008 2 2953   02:31pm 17 Nov 2008
plasmatronics regulator and wind gene Robert_VK2BBR, 24/09/2008 6 5957   07:52pm 16 Nov 2008
Laser Cutting Info? sodes, 08/11/2008 2 2987   11:51pm 15 Nov 2008
Power curve of F&P Smartdrive Kenneth, 11/11/2008 6 3071   05:13am 12 Nov 2008
Are these motors any use? MarkColeman, 11/11/2008 3 3592   10:32pm 11 Nov 2008
Jaycar mill - 300 - 500 W??? domwild, 11/11/2008 2 3268   11:09am 11 Nov 2008
F&P water pump turnymf, 07/11/2008 6 2989   06:37am 11 Nov 2008
alternator or generator? mick97, 09/11/2008 4 3164   12:49pm 10 Nov 2008
Not much idea BenG, 09/11/2008 4 2544   12:40pm 10 Nov 2008
furling revisited? Tinker, 02/11/2008 35 12586   01:06am 10 Nov 2008
Community Based Wind/solar power systems windstuffnow, 09/11/2008 7 2587   09:45pm 09 Nov 2008
= New posts since you last visited .      

   Page 65 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2025