Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 08:14 25 Jun 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 208280 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 524191   02:49pm 16 Dec 2015
Normal Topics  

   Page 53 of 99    

need help DTV004, 15/09/2009 21 7612   02:10am 27 Sep 2009
Fieldlines down? Gizmo, 24/09/2009 16 5643   03:57pm 26 Sep 2009
F&P Re-Wire Suggestions gblass1, 24/09/2009 6 4002   07:16pm 24 Sep 2009
New PVC blades windie-butt, 20/09/2009 10 3831   06:26am 24 Sep 2009
Magnetic levitation VAWT windie-butt, 24/09/2009 0 3107   01:26am 24 Sep 2009
link to piclogger file viewer GWatPE, 20/09/2009 0 3626   12:20am 20 Sep 2009
Building First F&P Wind Generator gblass1, 19/09/2009 1 3620   06:22pm 19 Sep 2009
heat from vawt garrymile, 16/09/2009 7 3960   11:34am 19 Sep 2009
El Cheapo hub & blades Barry T Coles, 18/09/2009 2 3405   07:33am 18 Sep 2009
1.5kw 3 phase motor Smart Drives, 08/09/2009 4 3808   05:06am 18 Sep 2009
Motor Help gblass1, 16/09/2009 6 4870   11:08am 17 Sep 2009
Are these motors any good as Generator? drw1978, 17/09/2009 3 3254   10:35pm 16 Sep 2009
Ropatec MacGyver, 15/09/2009 7 4852   04:23am 16 Sep 2009
“plug & play” grid tie inverters Wes Lemarr, 13/09/2009 3 3879   11:44am 14 Sep 2009
Curious wendallb, 08/09/2009 4 4601   03:26am 14 Sep 2009
Commercial 400-Watt Windcharger MacGyver, 07/09/2009 8 5023   05:16am 13 Sep 2009
Maximum F&P outputs. Downwind, 11/09/2009 7 4523   06:52am 12 Sep 2009
VAWT Question MacGyver, 11/09/2009 2 3773   06:01am 11 Sep 2009
F&P Vawt Pics floodrod, 10/09/2009 6 4779   10:14pm 10 Sep 2009
Windmill’s of the far north Greenbelt, 09/09/2009 1 4363   11:13am 09 Sep 2009
GE 5SME22NJ028 davef, 02/09/2009 6 5456   08:07am 09 Sep 2009
F&P Novice FlashmanAB, 06/09/2009 4 4979   10:08pm 06 Sep 2009
First mill, need advice on scaling specs oiko, 31/08/2009 7 4386   08:25pm 05 Sep 2009
dual fp setup makourain, 02/09/2009 2 6274   03:28pm 03 Sep 2009
Maxed out at 4amps dazler, 27/08/2009 11 4139   08:12am 02 Sep 2009
= New posts since you last visited .      

   Page 53 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026