Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 01:28 15 Jul 2025 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 306 176006 Chopperp  08:58am 07 May 2025
Forum Guidelines Gizmo, 11/12/2011 2 495467   02:49pm 16 Dec 2015
Normal Topics  

   Page 71 of 98    

New Wind Turbine Design PaulVAWT, 15/07/2008 6 3976   02:41pm 16 Jul 2008
hugh piggot turbine AMUN-RA, 19/04/2007 20 9976   02:30am 16 Jul 2008
New page - Phill’s RE gridtie system Gizmo, 04/05/2008 13 6548   10:08am 13 Jul 2008
1.2 Kw output " THE BEAST" fillm, 09/07/2008 6 4398   08:55am 13 Jul 2008
Welding complicated/alternate mounting? madteckhead, 04/07/2008 6 6174   11:09pm 12 Jul 2008
Nose cones robbo, 12/07/2008 2 3188   12:23pm 12 Jul 2008
testbed setup some testing done brucedownunder2, 20/04/2008 14 4825   10:02am 10 Jul 2008
Need some help with mini windmill jeen, 06/07/2008 26 11265   07:22am 10 Jul 2008
using a stepper motor? mahela007, 08/07/2008 1 3745   03:18am 08 Jul 2008
lg motors prophetski, 06/07/2008 3 3450   01:34pm 07 Jul 2008
how to figure out different volt coils/st newbie-from-pa, 29/06/2008 3 2957   11:55am 07 Jul 2008
charging AA batteries? mahela007, 06/07/2008 3 3549   03:53am 07 Jul 2008
Wooden Blade Carving Bryan1, 30/03/2008 24 9082   09:59am 06 Jul 2008
Australia BBDrums, 03/07/2008 4 4082   04:00pm 05 Jul 2008
Windmill thrust loading rber, 04/07/2008 3 3912   06:11pm 04 Jul 2008
towers BBDrums, 03/07/2008 6 2965   12:18pm 04 Jul 2008
magnets to stator count hoodlem, 02/07/2008 7 3144   01:15pm 03 Jul 2008
3kW Generator Unit Jason69, 04/07/2007 16 5619   04:41am 03 Jul 2008
The test bed brucedownunder2, 01/07/2008 2 2840   11:15pm 01 Jul 2008
BRUSH LOSSES FandPwithPVC, 24/06/2008 9 4251   11:33pm 30 Jun 2008
Maines got wind also BBDrums, 29/06/2008 11 2769   06:11pm 30 Jun 2008
alternator for low rpm mechamz, 29/06/2008 10 3232   11:06am 30 Jun 2008
Vertical axis windmill question Merlino, 25/06/2008 8 3117   03:46pm 27 Jun 2008
Pipe coupling imsmooth, 24/06/2008 5 3882   09:51am 27 Jun 2008
is this the right fisher & paykel washer? Jpm000001, 25/06/2008 2 2969   12:49pm 25 Jun 2008
= New posts since you last visited .      

   Page 71 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2025